Redland Heathland Concrete Tile


On all orders

Redland Heathland Concrete Tile - Pack of 16


exc VAT


  • Code: 666120
  • Brand: Redland
  • Availability: Call Us

Product Information

A concrete plain tile featuring variation in hanging length, irregular sides and subtle surface texturing finished with randomly applied fine sands which combine to create all the visual features of a handmade clay tile but at a fraction of the cost.

The range of colours has been carefully developed to offer real alternatives to the leading handmade clay tiles in the market.

And, as well as the quality, cost saving and aesthetic benefits, Heathland tiles embody far less CO 2 than their clay tile equivalents; good looks that cost you and the environment less.

Available Colours:

  • 666120: Manor House Mix
  • 666122: Wealden Red
  • 666123: Autumn
  • 666125: Ember
  • 666126: Elizabethan


Heathland Plain Tiles conform to BS EN 490: 2011 Concrete roofing tiles and fittings for roof covering and wall cladding - Product Specifications.

Variation in hanging length and linear cover is a purpose designed feature of this tile and therefore the relevant clauses of BS EN 490 do not apply.


Heathland Plain Tiles have been rigorously tested in the Group wind tunnel where combinations of high wind and driving rain are used to determine the tile performance with respect to wind loading and weathertightness. Tiles will meet all the requirements of BS 5534: 2014 Code of practice for slating and tiling (including shingles), providing Redland fixing recommendations are complied with.

Technical Details

Size 264 x 165 mm
Minimum Pitch 35°
Maximum Pitch 90° subject to fixing specification
Minimum Headlap 65 mm
35 mm
below 90°
at 90°
Maximum Headlap 88 mm
Minimum Gauge 88 mm
Maximum Gauge 100 mm
115 mm
below 90°
at 90°
Tile Thickness 13 mm
Hanging Length 244 mm approx
Linear Cover of 1 Tile 165 mm approx
Covering Capacity
60 tiles/m2
52 tiles/m2
below 90°
at 90°
Laid Weight 75 kg/m2
65 kg/m2
below 90°
at 90°
Weight per 1000 Tiles 1.25 tonnes approx
Weight per Pallet 1.01 tonnes approx
Battens Required 10 m/m2
8.7 m/m2
below 90°
at 90°
Batten Size 38 x 25 mm rafter centres up to 600 mm
Nail Size 40 x 2.65 mm
Tiles per Pallet 768
Tiles per Pack 64
Packs per Pallet 12


  • Tiles are stacked by wedging a tile vertically behind a batten to create a platform for a stack of tiles
  • Tiles must be laid broken bond in a half bond pattern, but the side lap may be reduced to a minimum of a third of the width of the tile (55 mm) in some circumstances, e.g. curved roofing
  • Tiles must be hung on their nibs
  • Adjacent tiles should be laid with a nominal gap of 1.5 mm, maximum 3 mm
  • At eaves, use double courses with purpose made Eaves/Top Tiles for the undercourse.
  • At verges and abutments, use Standard Plain Tiles and Tile-and-a-Halves in alternate courses.
  • Adjacent to hips and valleys, use Tile-and-a-Halves for raking cuts.
  • At side abutments, allow for stepped flashing and soakers.
  • At top courses use double courses with purpose made Eaves/Top Tiles for the top course.
  • For Winchester Cuts use two Tile-and-a-Halves per course. This detail must not be used to abut roof pitches below 40°or in exposed locations. In these cases, use soldier or double soldier courses.
  • Individual tiles can be laid unfixed or nailed
  • Always refer to FixMaster for a BS 5534-compliant fixing specification
  • When nailing, two nails must be used per tile
  • With mortar bedded ridges and top edge abutments, since the Eaves/Top Tiles hang on the top course of tiles they are fixed to the tile below with Top Tile Clips

Product Data Sheet